Espace de noms de la page (page_namespace) | 0 |
Titre de la page (sans l’espace de noms) (page_title) | 'How To Repair A Four Inch PVC Ball Valve' |
Titre complet de la page (page_prefixedtitle) | 'How To Repair A Four Inch PVC Ball Valve' |
Ancien modèle de contenu (old_content_model) | '' |
Nouveau modèle de contenu (new_content_model) | 'wikitext' |
Texte wiki de l’ancienne page, avant la modification (old_wikitext) | '' |
Texte wiki de la nouvelle page, après la modification (new_wikitext) | '<br>This article describes the 4-inch PVC Ball Valve and the different types of joints it can be used with. PVC is a form of plastic that is resistant to wear and tear. PVC is thermoplastic, meaning that it will soften at high temperatures, so the PVC does not need any chemical carriers to keep it pliable. This means PVC joints can withstand extreme temperatures, which is why they are used on plumbing fittings. These PVC ball valves also have an internal mesh to aid the flow of liquid.<br><br><br>The PVC valve is available in both black iron and aluminum. These types of ball valves are able to provide watertight joints near most pipe fittings, especially those that are located above the water level. If you adored this information and you wish to get more info about [https://www.shunchengvalve.com/butt-weld-ball-valve/ click through the up coming webpage] i implore you to go to our webpage. This 4 inch PVC ball valve is made from polyvinyl chloride (a.k.a. 'PVC') for durability and flexibility.<br><br><br>These PVC joints can be installed inside the house or outside. Installing a PVC pipe valve outside is easy because these valves do not require exposed pipe walls or joints. If you are using a PVC joint, then make sure you position the valve to the valve seat face away from where you water is coming from. Positioning a valve inside the house is more difficult, because you must seal off the outlet pipe. You can do this by installing a drain-back pipe, but you may not have the room to do this if you are planning on doing a full plumbing renovation.<br><br><br>Installing a ball valve is very simple and you can do it yourself without hiring anyone to do it for you. To install the four inch ball valve, you will need the following: Four inch pipe fittings near the spout of the pipe that leads to your home. Attach the pipe fittings near the spout. Clean out any debris and dirt that might clog the ball valve.<br><br><br>Turn on the water in your home. Close the water valve that runs to the back of the valve box. Place the ball on top of the valve seat and push the button on the side of the valve to open the valve. The water should flow into the pipe that leads to the other end of the pipe. Make sure the water flows to the floor drain. Open the valve again to close it.<br><br><br>Attach the valve seat to the ball joint. You will need to use a plumber's putty to hold the seat in place. Make sure the valve seat is securely in place, because if it slips, the ball will be unable to grip the water pipe. Plumber's putty is an inexpensive and easy to use tape.<br><br><br>If the water does not flow through the PVC pipe or the valve malfunctions, turn the power off to the mains. Turn on the water heater to make sure the valve is open. Turn on the hot water and check the pressure from the meter. If there is not enough pressure, you may have to call a plumber or have the water heater serviced.<br><br><br>Clean the pipe that leads to the ball valve. Use a spray bottle to clean the exterior of the pipe. Clean the inside of the ball joint with a solvent or with water. Turn on the hot water to flush the solvents out of the pipe. Turn on the shut off valve for the main line to prevent water damage. Turn off the water shut off valve for the water shut off system.<br><br><br>Reconnect the water valve box to the main line and fill the PVC pipe with water and air. Make sure the ball fits securely in place. Apply grease to the ball joint as well as the pipe joints. Connect the ball valve box and turn the power back on to check pressure. If problems are found, they can usually be fixed by replacing the valve. For leaks, this process needs to be repeated.<br><br><br>Open the valve to release the trapped air. Fill the pipe again with water and allow it to settle. Turn on the shut off valve to prevent water damage. Run several test tips to ensure water is flowing through the pipe. If the water is not flowing through the pipe, have the faucet or sprayer repaired.<br><br><br>Replace the valve box if necessary and turn the power back on to finish the repairs. Turn on the waterline to ensure it is functioning correctly. If no problems are found, replace the ball valve according to manufacturer's instructions. With some simple troubleshooting, a PVC ball valve should be trouble free.<br>' |
