Journal des déclenchements du filtre anti-abus

'<br>[https://www.castermetal.com/ductile-cast-iron/ Ductile iron], cast aluminum, and stainless steel frying pans all need seasoning to prepare for use. Each different seasoning chemical has its own properties of increasing heat transfer, decreasing absorption, or maintaining a specific internal temperature. Ductile iron, copper, and black plastic pipe are the most commonly used seasoning substances.<br><br><br>Cast Aluminum: Cast aluminum pans, especially those with non-stick surfaces are vulnerable to cracking. Regularly check the seasoning rub or seasoning oil in your stainless steel pan after use. If any surface cracks, do not clean it. The seasoning oil should seal the crack. Use a damp rag to remove excess seasoning oil from cracks.<br><br><br>Aluminum: Aluminum is a good choice to season your carbon steel pan with. It heats up easily and responds to heat more quickly than stainless steel. Cast aluminum also heats up slowly and more evenly than other metals. You can apply oil to a flat plate of aluminum pans or on hot surfaces using a drip ring. Just remember to keep your pan seasoned to maintain your smoking point.<br><br><br>Cast Iron: This coating isn't as useful as stainless steel. A stainless steel pan is non-stick, which means rust will set in much easier, especially with metal utensils. However, a cast iron pan will retain its heat for a longer time, which will reduce the time you will need to season. If your pan is getting too hot, put a bit of oil over the top to maintain your smoking point. If your pan has rusted, you can strip off the rust and then re-season the pan.<br><br><br>Hot Water: If your coating has been sitting on the pan for a while, you may notice that it gets sticky when you try to remove it from the heat. The best way to deal with this problem is to rinse off the pan with hot water. After the water dries, you should be able to brush a bit of oil over the top and then use a clean rag to gently peel off the food stuck on the pan.<br><br><br>Other Non-Carbide Metals: If you aren't using a stainless steel or cast iron pan, you can still seasoning your pans with oils. There are several oils that you can use, such as vegetable oil, grapeseed oil, or canola oil. You'll find these are very compatible with cooking and baking, and they will leave your pans with a good sheen.<br><br><br>Soap: Soap works great with any cooking or baking endeavor. If you're going to use acidic cleaners, make sure you use products that are designed for stainless steel, and then follow the directions carefully when you apply them to the pan. Cast iron will react differently to acidic cleaners, so only use a non-acidic cleanser if you have a cast iron pan. For baking, however, you can safely use both vinegar and soap without any damage to your pans.<br><br><br>Stainless Steel Moisturizer: You can also use a stainless steel moisturizer after scrubbing the pan with a non acidic cleaner. Be sure to only spray a thin layer of the cream onto the pan so the heat does not melt the cream. This will prevent scaring. Just dab a small amount of the moisturizer over the heat until the area is thoroughly clean and then wipe it off. Using a clean kitchen cloth is highly recommended here as well.<br><br><br>Cracked Glass Coating: Sometimes food will become stuck in between the pan's finish and the steel finish, and this will cause a small puddle of liquid to form. This will go away quickly if you let it air dry. However, if the glass is already cracked, you will have to put that piece of glass into a hot water solution to get it back into a smooth state again. Do not try to heat up the glass, as it will permanently weaken the metal. Once the piece has cooled off completely, coat it again with the coating to protect it from further harm.<br><br><br>Rust: This is a problem with aluminum that does not have an enamel coating. Normally you won't see rust unless you have very heavy metals or very old pieces. However, with cast iron pans you can still see some rust if the finish has become dull over the years. This can be fixed by applying an exterior coating of paint to it. It is best to wait until the paint has fully dried before using the pan, though. This will keep it looking new for much longer.<br><br><br>So, now that you know these three signs, you are better prepared to use your newly oiled and seasoned steel pan. Just remember to always put a thin coat of oil onto the surface before you heat it. Also, before seasoning your pan, coat it with a non-stick coating to prevent the formation of rust on the metal when you do heat it. And finally, once you're finished cooking on your new pan, always make sure to wipe off the excess seasoning so that the non-stick coating stays on.<br>'